Audioarts HS-1 Headphone Station
The Audioarts HS-1 is a tiny ( 2-3/4" by 3-3/4") headphone station designed for broadcast use. It can be used as a free-standing unit or mounted underneath the counter with an optional bracket. Performance is clean, quiet and powerful, with wide dynamic range and ruler flat frequency response. The front panel has a 1/4" output phone jack, power LED and rotary level control. An internal HI/LO gain switch lets you match a wide range of input types.
Rear connectors include dual RJ45 parallel inputs and 9VDC power in, that (like the TS-1) multiplies voltage and current to provide GREAT, LOUD sound to headphones of virtually any impedance. Input cable and special 9VDC negative center pin power supply included.
GAIN: +5dB LO setting, +14dB HI setting
DISTORTION:
THD+N .003%
IMD .005%
SMPTE DIN .001%
NOISE: -95dBu 20KHz BW, unweighted
MAXIMUM OUTPUT:
voltage +20dBu
power 180mW
current 65mA
MAXIMUM INPUT LEVEL: +26dBu
DYNAMIC RANGE: 115dB
CMRR: 80dB
DIMENSIONS (countertop): width 2.75”/7cm, height 0.95”/2.41cm, depth 3.125”/9.6cm, level knob adds 0.625"/1.59cm
DIMENSIONS (w/added undercounter bracket): width 3.9”/9.9cm
Audioarts TS-1 Talent Station
The Audioarts TS-1 is a tough, compact countertop unit that utilizes a high-gain headphone amplifier that multiplies voltage and current to provide GREAT, LOUD sound to headphones of any impedance. It features 1/4” and mini stereo output jacks, two panel switches with internal LEDs, a power light and a level control. An internal HI/LO gain switch lets you match a wide range of input types.
There's a LOGIC RJ45 that lets you to use the two front panel switches for TB, COUGH and other functions. INPUT and OUTPUT connectors follow standard Studio Hub RJ45 analog audio pinouts. The OUTPUT feed allows you to daisychain the unit’s source audio to other devices. USB power supply and cable included.
Wiring is through cutouts in the bottom of the unit.
CONNECTIONS: The USB port provides +5VDC power to the amp. The LOGIC RJ45 lets you to use the two front panel switches for TB, COUGH and other functions. INPUT and OUTPUT connectors follow standard Studio Hub RJ45 analog audio pinouts. The OUTPUT feed allows you to daisychain the unit’s source audio to other devices.
COUNTERTOP MOUNT: To install the TS-1 you will need to drill six holes in your countertop: four thru-holes for wire passage (5/8” diameter spade bit, shown in red) and two mounting holes (1/8” drill bit, A and B) for the 3/4” screws that will hold the unit in place.
A drilling template is included in the packing box.
Once the wiring is connected and everything is working properly (don’t forget to set the HI/LO gain switch) it’s time to fasten the TS-1 to the counter.
To do this you need to remove the unit’s two acrylic sideplates (each held in place by three philips head screws). You can then drive home screws through the A and B counter mounting holes in the bottom plate (sharp point 3/4 inch #8 sheetrock screws recommended).
Once anchored in place, close up the unit by replacing the sideplates.
GAIN: +5dB LO setting, +14dB HI setting
DISTORTION:
THD+N .003%
IMD .005%
SMPTE DIN .002%
NOISE: -92dBu 20KHz BW, unweighted
MAXIMUM OUTPUT:
voltage +20dBu
power 650mW
current 120mA
MAXIMUM INPUT LEVEL: +26dBu
DYNAMIC RANGE: 112dB
CMRR: 80dB
DIMENSIONS: width 5.4”/13.7cm, height 1.8”/4.6cm, depth 3”/7.6cm
WEIGHT: 10oz/.28kg